Choosing a metal roof starts with the design and the conditions of the roof it will cover, not with the metal alone. MQ Roofing, based in Tomah, WI and in business since 2008, installs metal roofing, including standing seam metal, for Wisconsin homeowners. This guide explains the questions that should shape a metal roof system choice, including the difference between exposed-fastener and concealed-fastener panels, and what a written system specification should say.
Two metal roofs can look similar from the street and perform very differently, because the panel profile, fastening method, flashing, underlayment, and substrate all work together. The more of those details a proposal spells out, the easier it is to compare options fairly.
Metal Roofs and Their Benefits

Homeowners usually look at metal for reasons that tie directly to Wisconsin weather and long-term ownership. The comparison of metal roofing materials covers the material side in more detail. In general, metal roofing is chosen because:
- Snow and rain shed well: Depending on the slope, panel and weather, smooth metal surfaces may shed snow and rain, which matters on roofs that see winter loads and freeze-thaw cycles. Roof pitch, snow retention, and eave details decide how that sliding snow is managed.
- Weather resistance depends on details: Metal can perform well in wind, rain, and hail, but results depend on the panel, fastening, and flashing, not on the material alone. Standing seam features are one example of how design affects performance.
- Long service life with care: Metal roofs are known for lasting a long time when installed correctly and maintained, but no responsible contractor can promise a specific number of years without knowing the roof and product.
- Reflective finishes: Some finishes reflect more solar heat than others, which can affect cooling load. Ask for the actual finish data rather than a general percentage.
Exposed-Fastener and Concealed-Fastener Metal Roofs
The most useful design decision is how the panels are attached. In an exposed-fastener system, screws pass through the face of the panel and are visible on the roof. In a concealed-fastener system, such as standing seam, panels are held by clips or similar hardware under the seam, so the roof surface has no exposed screw heads.
- Exposed fasteners: The screws and their washers are wear items. Metal expands and contracts with temperature, and over time the fasteners and seals may need to be checked and sometimes replaced. Careful installation and an inspection plan matter more.
- Concealed fasteners: Appropriately selected fixed or floating clips can accommodate panel movement and avoids through-panel fasteners across much of the roof field. The system generally involves more detailed trim and flashing work and a higher up-front installation scope.
Neither system is right for every roof. The better question is which one fits your roof geometry, budget, and how much maintenance access you want to plan for. MQ Roofing’s residential metal roofing page and its standing seam page describe the systems it installs.
Roof Conditions That Should Guide the System Choice
Use this table to turn the roof’s actual conditions into questions for your contractor.
| Condition | Why it matters | Question to ask |
|---|---|---|
| Roof geometry and pitch | Low slopes, steep slopes, valleys, and dormers change panel layout, trim, and water and snow flow. | Which panel and fastening method suits this pitch and layout? |
| Movement and temperature swings | Metal expands and contracts, and the fastening method decides how that movement is accommodated. | How does the system allow for panel movement? |
| Substrate and deck | Deck condition and underlayment affect attachment and water management; ventilation and insulation also influence condensation risk. | Will the deck be inspected, and what underlayment is specified? |
| Flashing and penetrations | Chimneys, vents, skylights, and walls are common leak points. | How will each penetration be flashed and sealed? |
| Maintenance access | Exposed fasteners and seals may need periodic checks, and some roofs are hard to reach. | What inspection or maintenance should I plan for? |
| Finish and trim | Coatings and trim details affect appearance, wear, and edge protection. | What finish is specified, and what written finish terms apply? |
What a Written Metal Roof Specification Should Include

Ask each contractor for a specification, not just a price. A clear one names:
- The panel profile and whether the system is exposed-fastener or concealed-fastener.
- The metal, thickness, and finish, as named product information.
- The underlayment, deck repairs, and how hidden damage will be handled.
- Flashing and trim details at eaves, ridges, valleys, walls, and penetrations.
- Snow retention or other accessories, where the roof calls for them.
- What is excluded, how extras are approved, and who handles cleanup.
- Workmanship and product warranty terms, described in writing and attributed to the right party.
What Affects the Cost of a Metal Roof
Cost follows the specification. Panel type and finish, roof size and complexity, the amount of trim and flashing, deck condition, and access all change the price. Concealed-fastener systems may require different panel profiles and detailing than exposed-fastener systems, and a roof with many valleys, dormers, and penetrations takes more labor than a simple gable. Compare the specified roof assembly and any permitted changes to the scope, including any hidden deck repairs, before comparing totals.
Choosing a Metal Roof System for Your Home
A good metal roof decision comes from matching the system to the roof, then putting that match in writing. For more on the services involved, see metal roofing and siding. To discuss your roof with MQ Roofing in Tomah, WI, call (608) 553-3300 or use the contact page.
Frequently Asked Questions
What is the difference between exposed-fastener and concealed-fastener metal roofing?
Exposed-fastener panels are screwed through the face and the screws stay visible. Concealed-fastener systems, such as standing seam, attach panels with clips under the seam.
Which metal roof system is better for a home?
It depends on the roof’s geometry, budget, and maintenance plans. Ask for a written specification that explains why a system fits your roof.
Does a metal roof need maintenance?
Yes. Exposed fasteners, seals, flashing, and drainage should be checked periodically, and the right schedule depends on the system installed.
Does MQ Roofing install standing seam metal roofing?
Yes. MQ Roofing installs metal roofing, including standing seam metal, for residential customers.
